At the factory, we put a large radius on the tubular handle to provide
clearance when using the Lee Safety Prime System.
You will need:
(1) 90933- 4 Hole Update Kit with Auto Index
http://leeprecision.com/4-hole-update-kit-w-ai.html [1]
(1) TA2269- Auto Index Press Ram
http://leeprecision.com/auto-index-ram.html [2]
Links:
------
[1] http://leeprecision.com/4-hole-...
There are a number of possible causes for this.
1. Check shellholder alignment with ram; If there is a burr or
spilled powder or some other foreign debris that prevents the
shellholder from slipping all the way into the ram, the primer guide
(t...
The Turret Press is a great press for loading rifle cartridges. If you
choose to load cases that are over 2 5/16\" in length, the Auto
Indexing feature of the Press must be disabled. This can be done in
mere seconds by simply taking the actuator rod ...
Turret Press Help Videos available:
http://leeprecision.com/Turret-Press-Help.html [1]
The most common cause for the Three hole Turret press to fail to
index is an over tight clamp screw. This collapses the clamp (the
clamp is the two die cast ...
To ensure ease of removing and installing a Turret, here is a short
reminder. The Turret turns as the press Ram is lowered. This is due to
the Square Ratchet riding on the Index Rod. The Square Ratchet is
designed to last nearly indefinitely and resi...
We do not have any 3 hole turret press index rods available.
You would have to purchase the update kit # 90933, and that would
include a new index rod, and convert your press to a 4 hole turret
model. http://www.leeprecision.com/4-hole-update-k...
This press was discontinued in the late 90's.
If you are looking for replacement Nylon Ratches, they are available
here: http://leeprecision.com/hex-ratchet.html
If you have a LEE Turret Press, there is a limitation to how long a
cartridge you can load and automatically index. With the LEE Turret
Press the maximum cartridge length is 2-5/16" long, LEE Classic Turret
Press 3-1/16" long. If you are loading c...
Capable of 250 rounds per hour for handgun cartridges
We do not have 3 Hole Auto Index parts available to convert a 4 Hole
Turret Press with Auto Index to a 3 Hole Turret Press with Auto Index.
The 3 Hole Auto Index press was discontinued in the late 1990's.
You can convert the Turret press to the Pro-1000, but it isn't very
cost-effective. The parts necessary to make the conversion will cost
about $120, and one can frequently find new Pro-1000's for sale from
our larger dealers for around $130.
Pa...
To disable the auto index feature of your press, simply remove the
turret, lift the index rod out and replace the turret. You can now use
your press like a single stage press and hand index the turret to
change
dies.
Primer tipping or flipping is usually caused by a burr or nick in the
slot of the ram where the primer arm and primer cup pass. This burr
catches the primer cup and compresses the spring and when it suddenly
snaps free, it causes the primer to tip or...
The free play in the turret is normal. Without it, the turret would
not move correctly. Make sure that the die is adjusted to compensate
for
the free play.
* Remove right front bolt
* Finger tighten bolt and washer on bracket (washer flat must face
the turret)
* Install tray and trough assembly
* Algn bracket so that the trigger assembly lines up with the primer
arm
* Hold the bracket in pos...
To update your press for the Safety Prime you will need these parts:
TP2269 - Auto Index Ram - $7.00
BP2889A - Small Primer Arm - $7.00
BP2889B - Large Primer Arm - $7.00
Premature nylon hex ratchet wear is caused by over tightening the
clamp halves. This causes the clamp to grip the nylon & cause failure.
HOME CURE: reduce the diameter of the nylon hex ratchet by grinding
off approximately 1mm, or put a round o...
We do not have a great means to mount the Perfect powder measure to
either press. It is not advisable to mount to either press for several
reasons. If using the Universal Powder Charging die for rifle cases,
there is no where to attach the return ...
The primer arm slips into the slot in the ram. The little hook on the
arm catches on a pin that is in the slot. Now as you raise and lower
the ram, the primer arm pivots in and out of the slot. The cup on top
of the primer arm is where a primer is pl...
You need to look at the slot in the ram for a burr or a nick. You can
take a fine file or sharpening stone to break the edge of the slot and
remove any burr. The primer arm should travel freely in the slot.
Check the Primer arm for any nicks also.
Try both primer arms in the press using the same shell holder. If only
one sticks, then the problem is probably related to the primer arm
assembly. If they both stick, then the problem could be the ram or the
shell holder. Be sure to test this with a...
Try both primer arms in the press using the same shell holder. If only
one sticks, then the problem is probably related to the primer arm
assembly. If they both stick, then the problem could be the ram or the
shell holder. Be sure to test this with a...
To get the spent primer disposal to operate as intended, the L-Shaped
steel primer arm needs to be in the ram during depriming. This directs
the flow of spent primers into the cavity that they need to go.
There is a kit available to update your Pro 1000 and Turret Press to
the new ergonomic grip roller handle. Consists of new toggles, roller
handle assembly, ram pin, lever clamp, bolt and washer. Toggles TP3007
and TP2128 are no longer available an...
We changed the T shaped primer arm assembly design about 10 years ago,
and don't have any T shaped primer arms available. You would need to
purchase a new ram and the large and small primer arms.
Ram: http://leeprecision.com/auto-index-ram.html [1]
...
To switch cartridges on the Turret press, all that is needed is the
appropriate set of dies. The shell holder needed comes with Lee dies
(except RGB). Changing the priming consists of removing the primer
arm, and installing the appropriate size. Whil...
Reloading process demonstrated download video [1]
Safety Prime installation download video [2]
Turret Press in operation download video [3]
Removing and Installing a Turret download video [4]
Four hole turret index adjustment downl...
The square ratchet is both free to rotate inside the clamp and held
fast by the clamp, depending on which direction the ram is moving. If
you are lowering the press lever (raising the ram) you don't want the
turret to rotate, so the square ratchet mu...
Primer guide cup contacting bottom of shell holder
LEED Engineering produces a turret rack holder:
http://www.leedengineering.com/reload.html [1]
Links:
------
[1] http://www.leedengineering.com/reload.html
Included with the Deluxe and Classic Turret Presses is a spare black
plastic ratchet. This installs inside the black auto index clamp on
the steel ram. The square black ratchet rides on the 1/4"x 1/4" steel
index rod. When removing the aluminum tu...
Help Desk Software by Kayako Resolve